2204984 Wilo United States Sales

Yonos GIGA2.0-I 50/1-13/1.5 Inline pump with high energy efficiency with EC motor of the Efficiency class IE5 in accordance with IEC 60034-30-2, hydraulic Minimum efficiency index MEI = 0.4 and electronic Power adjustment in dry runner design. The pump is designed as a single-stage low-pressure centrifugal pump with flange connection and mechanical seal. The Yonos GIGA2.0-I is a priority for pumping heating water (according to VDI 2035), cold water and water-glycol mixtures without abrasive materials designed in heating, air-conditioning and cooling systems. Construction: - Single-stage low-pressure centrifugal pump with undivided shaft in Block construction - inline spiral housing (suction and discharge pipe with same flanges in a line) - PN 16 flanges - in accordance with EN 1092-2 - Pressure measurement connections (R 1/8) for attached Differential pressure transmitter (version... -R1 without differential pressure sensor) - pump housing and lantern/motor flange as standard with cataphoresis coating - Mechanical seal for water delivery up to Tmax. = +120°C. Up to T = +40°C, a glycol admixture of 20% to 40% is Volume percentage allowed. In the case of water-glycol mixtures with fractions Glycol > 40% to max. 50% by volume and one Media temperature from > + 40°C to max. +120°C or others Media other than water is an alternative Provide a mechanical seal. - Supply voltages: 3~440 V +-10% 50/60 Hz; 3~400 V +-10 % 50/60 Hz; 3~380 V - 5% +10% 50/60 Hz Rule types: - Variable differential pressure (dp-v) - Constant differential pressure (dp-c) - Constant speed (n-const.) - User-defined PID control Features: - Dual pump operating modes: main/reserve mode, Efficiency-optimized addition mode for dp-c and dp-v - Integrated full motor protection Display on the “home screen” of the graphical display: - Currently set control type - Current target value - Current actual value - Current flow rate (only when connected differential pressure sensor) - Current power consumption Execution: - 1 analog input: 0... 10 V, 2... 10 V, 0... 20 mA, 4... 20 mA only for sensor value from differential pressure sensor - 1 analog input: 0... 10 V, 2... 10 V, 0... 20 mA, 4... 20 mA only for external setpoint sensor - 1 digital input (Ext. OFF) - 1 alarm relay for optional use for operational or fault messages - Slot for Wilo-CIF modules with interfaces for GA building automation (optional accessories: CIF Ethernet modules, Modbus RTU, BACnet MS/TP, LON, PLR, CAN) - Wilo Net as a Wilo system bus for communication with double pump operation - Automatic emergency operation in special conditions (pump speed can be defined) e.g. in the event of failure of Bus communication or from sensor values - Rotatable graphical color display (2 inch) operated via One button hand control panel - Integrated double pump management (double pumps are ready wired), when using 2 individual pumps as Double pump unit, connection via WILO Net - Cable break detection with an analog signal (in connection with 2 ... 10V or 4... 20mA) - Standard condensate drain holes in the motor housing (with Delivery locked) - vent valve on the lantern Package includes: - pump - Installation and operating instructions and declaration of conformity Accessories (must be ordered separately): 3 consoles with mounting material for foundation construction - Blind flanges for double pump housings - To connect to building automation: - CIF PLR module - LON CIF module - BACnet MS/TP CIF module - Modbus RTU CIF module - CANopen CIF module - Ethernet multiprotocol CIF module (Modbus TCP, BACnet/IP) - M12 RJ45 CIF Ethernet connector - DDG 2... 10V differential pressure transmitter - DDG 4... 20mA differential pressure transmitter Operational data Delivery medium: water 100% Media temperature: 20.00 °C Requested flow rate: 21.00 m³/h Requested delivery height: 12.00 m Media temperature: -20... 120 °C Ambient temperature: 0... 50 °C Maximum operating pressure: 16 bar Minimum efficiency index (MEI): ≥ 0.4 motor data Motor efficiency class: IE5 Interference emission: EN 61800-3 Immunity to interference: EN 61800-3 Power supply: 3~400 V/50 Hz Rated motor power: 1.4 kW Max. speed: 2570 rpm Nominal current: 2.5 A Insulation class: F Motor protection class: IP55 Motor protection: KLF integrated materials Pump housing: 5.1301/EN-GJL-250 Impeller: PPE/PS-GF30 Wave: 1.4021 Shaft seal: AQ1EGG Lantern: 5.1301, EN-GJL-250 KTL coated Installation dimensions Suction side pipe connection: DN 50, PN 16 Pressure-side pipe connection: DN 50, PN 16 Overall length: 340 mm